The Quilt Shoppe · Mabel & Ethel's
← All guides

Log Cabin Quilt Block Tutorial — Cutting Math, Sewing Order & Classic Layouts

The log cabin is the block that turns scraps into heirlooms: a center square, strips added in order, one light side and one dark side — and suddenly the same humble unit composes itself into barn raisings, sunshines, and diagonals that look far more planned than they are. It is also the best block in quilting for using up scraps, which is why a century of quilters — from the silk-salvage quilts of the 1880s to the feedsack era — kept returning to it. This tutorial covers the traditional construction from the center outward, the math that scales to any size you want, and the small habits (pressing direction, trimming, sewing order) that keep a sixteen-block layout flat.

The Anatomy of a Log Cabin Block

A log cabin block is built entirely from the center out, in a clockwise spiral:

That light/dark diagonal is the entire design engine. One block looks like a diamond; a grid of them looks like whichever layout you choose — which is why identical blocks make radically different quilts.

The Cutting Math

Log cabin math is friendlier than it looks because every strip is the same width. In finished sizes:

PieceFinished sizeCut size
Center square2″2.5″
Logs (each round adds 1″ per side)1″ wide, lengths vary1.5″ wide, lengths vary
Block after 5 rounds2 + 2 × 5 × 1 = 12″12.5″

The log lengths are the only part that changes as you sew: each new log must match the current edge it covers, which grows every round. Two ways to handle it: measure-and-cut as you go (accurate, slightly slower), or the traditional strip-piecing shortcut in the next section, which avoids measuring altogether. Want a bigger block? Add rounds, widen the strips, or enlarge the center — the formula holds. To size a whole quilt from these blocks, run your numbers through the quilt size calculator.

Sewing the Block, Step by Step

Set up the spiral

Choose a direction — clockwise is conventional — and never break it. Every log goes on the same side sequence: for a clockwise spiral starting at the center's right edge, the order is right, top, left, bottom, then repeat. Number the sides on a scrap of paper if it helps; the single most common beginner error is a log sewn to the wrong edge, which turns the spiral into a tangle and breaks the light/dark diagonal.

Add each log

  1. Place the log right sides together with the current edge, right sides aligned, and sew with a true scant quarter-inch seam.
  2. Finger-press, then press the seam away from the center, always. The allowances end up fanning outward like spokes, which is exactly what keeps the middle of the block flat instead of bulged.
  3. Trim the log flush with the edge it extends past (a small square ruler works well for the first rounds).

The strip-piecing shortcut

To skip measuring: cut a stack of light strips and dark strips 1.5″ wide, a couple of inches longer than needed. Sew each log slightly long, press, then trim flush — the excess disappears and every length self-corrects. This is also a natural chain-piecing workflow when making many blocks: sew log #1 on ten centers in a row, then log #2 on all ten, and so on. The order discipline matters more, not less, in batches — a mixed-up spiral across blocks is invisible until the layout starts looking slightly drunk.

Press and square between rounds

Press every seam as described in our pressing guide — lift and lower, never slide, especially across the bias-adjacent edges the growing block exposes. After every two or three rounds, check the block against a square ruler and trim the outer edges only, never the center. Small corrections each round beat one brutal squaring-up session at the end, because drift in log cabins compounds: a log trimmed crooked in round two pushes every later log.

The Center Bulge Problem

Almost every first log cabin arrives slightly puffy in the middle, and the cause is arithmetic: five rounds stack ten seam allowances around one small square. The defenses, in order of importance:

Layouts: One Block, Many Quilts

Rotate the blocks as you arrange them and the same unit makes different designs — this is the log cabin's party trick:

Lay blocks on a design wall or the floor and step back before sewing rows together — the rotation choices are invisible one block at a time and decisive across a grid. Photograph the arrangement on your phone before picking anything up; the picture keeps the layout honest through the rows-to-quilt-top stage.

Variations Worth Knowing

Courthouse Steps

The same idea with a different sewing order: logs are added in pairs — one to the top, one to the bottom, then one to each side — instead of a spiral. The color split runs vertically down the middle instead of diagonally, and the blocks read as steps. Same math, same strip width, different sequence.

Foundation piecing

For scrappy blocks from irregular strips, sew each log onto a fabric or paper foundation with a sew-and-flip motion — the foundation guarantees square even when the strips aren't. Paper foundations are printed oversize and trimmed to exact size afterward; fabric foundations stay in the quilt. It is slower per block but nearly foolproof, and it is the traditional method for the wonky silk and velvet log cabins of the 1880s–1900s.

Curved and pineapple

Curved log cabin uses narrow logs on one side and wide on the other, and the block bows into a soft arc — layouts of it ripple. Pineapple adds corner triangles to each round so the logs become points; it is the log cabin's ambitious cousin and a good second project once the basic block feels automatic.

The Bottom Line

The log cabin rewards two habits and forgives nearly everything else: an unbroken spiral direction, and seams pressed away from the center every time. Add the trim-as-you-go discipline and the strip-piecing shortcut, and it becomes the perfect beginner-adjacent project — precise enough to teach real skills, scrappy enough that no fabric budget stands in the way. Start with one block, then let the layouts argue for the quilt.

Nothing here is professional conservation or appraisal advice. For antique quilt repair or textile care questions, consult a textile conservator.

Frequently Asked Questions

What does the red center of a log cabin block mean?

Traditionally the center square is red (the hearth or chimney of a pioneer home) or yellow (a lighted window), and everything else is built around it: lighter strips on one side to catch the sun, darker strips on the other for the shaded walls. The color code is optional today, but the light-side/dark-side split is what gives every log cabin layout its pattern.

How do I calculate the strip size for a log cabin block?

Work in finished sizes and add the seam allowance at the end. A block's finished size equals the finished center plus twice the number of rounds times the finished strip width: for the classic block — a 2-inch finished center (cut 2.5″) with 1-inch finished strips (cut 1.5″) and five rounds per side — that is 2 + 2 × 5 × 1 = a 12-inch finished block (12.5″ unfinished).

Why is my log cabin block bulging in the middle?

Usually it is the seams piling up in the center: every round's seam allowance stacks toward the middle, so five rounds hide ten seam allowances' worth of thickness. The fixes are pressing every log away from the center as you go, a true scant quarter-inch seam, and a light trim of the block edges — not the center — after each round.

Ready to stitch?

Everything mentioned in this guide, picked for beginners.

Shop quilting supplies on Amazon ↗

Sponsored link — we may earn a commission at no cost to you.